Atwood 8940 Iii Dclp Troubleshooting

Please verify which kit is applicable to your furnace prior to ordering.

  1. Atwood 8940-iii-dclp Parts
  2. Atwood 8940 Iii Dclp Troubleshooting
  3. Atwood 8940-iii-dclp Troubleshooting
  4. Atwood 8940 Iii Dclp Troubleshooting
  5. Atwood Model 8940-iii-dclp Parts

Tune-Up Kit #1 (Single Sense Electrode) Includes:

Atwood 8940-iii-dclp Parts

Parts

Atwood 8940 Iii Dclp Troubleshooting Leakin Park Map Serial.pdf Civilization 5 Sdk Crack Webpack Stats Analyzer Shank 2 Download Pc Kodek Mpc Win Xp 2000 Download My Life Eckow Oftalmologia Clinica Jack J. Kanski Epub Download Free Online Virtual Horse Games 3d. It is 120 v ac, but the solinoinds say 24vdc.they ohm at 045. The local apsc say i have to change the whole valve.the blower works. It will fire for about a second and won't relite. But the blower and fan keep ruunning. That's why i think it is the gas valve.like on a gas dryer.the part @'s on the valves are c5308 & c5305 both 2 wire. Atwood Mobile Products 8940 Furnace User Manual. THIS INSTRUCTION MANUAL IS FOR USE BY AN AUTHORIZED SERVICE. TECHNICIAN TO INSTALL AN ATWOOD - hydro flame. DCLP-III DCLP-III ACLC-III ACLC-III. BTU Input 35,000 40,000 35,000 40,000. Output BTU/HR 27,300 31,200 27,300 31,200. Type Gas LP LP LP/NAT LP/NAT.

Atwood 8940 III DCLP won't stay lit: Deniseg: RV Systems & Appliances: 4: 05:11 AM: Wiring connections on Atwood 8940 III control board: drive805: RV Systems & Appliances: 2: 12:25 AM: Replace old Atwood Water Heater With New Atwood Water Heater: GlennLever: RV Systems & Appliances: 2: 10:41 AM: Atwood Landing. Atwood / Hydro Flame Furnace Model 8940-AC-III Tune-Up Kit comes in two variations. The first (Kit #1) has a single sense electrode (one wire that goes to the electrode), the second (Kit #2) has a dual sense electrode (two wires that go to the electrode).

  • Item# 36 Sail Switch 36680(New P# 31377)

Tune-Up Kit #2 (Dual Sense Electrode) Includes:

  • Item# 36 Sail Switch 36680(New P# 31377)

Atwood Furnace 8940-DC-III Exploded Parts Views & Available Downloads
Please Click The Down Arrow To View More
Item# 1 Klixon Relay 48000
Item# 2 Thermostat, Brown 38452 NLA
Item# 2 Thermostat, White 38453
Item# 3 Duct Cover 31361
Item# 4 Duct Adapter, 4 Inch 31474
Item# 6 Orifice 31077
Item# 7 Combustion Air Wheel 33128
Item# 9 Motor Gasket 37713 (Replaces P# 32841)
Item# 10 Gas Valve 31155 Before S/N 0657716
Item# 10 Gas Valve 38604 After S/N 0657715
Item# 11 Replacement Coil, DC Valves Only 31000 NLA
Item# 13 Gas Inlet Plug 33567 Before SN 0657716 NLA
Item# 13 Gas Inlet Plug 37410 After SN 0657715
Item# 19 DSI Board Bracket 34541
Item# 20 Slide Plate 37442 Before S/N 0657715
Item# 21 Circuit Breaker 33782, 15 Amp
Item# 21 Circuit Breaker 34015, 20 Amp
Item# 22 Screw Latch 33847
Item# 23 OEM Ignition Board 31501
Item# 23 After-Market Ignition Board 31501MC
Item# 27 Blower Housing
Item# 34 OEM Blower Motor Kit, DC Voltage 37357
Item# 34 After-Market Blower Motor Kit, DC Voltage 37357MC
Item# 34 Motor Only, DC Voltage 37698 NLA
Item# 35 Motor Mount Bracket, DC Motor Only
Item# 36 Sail Switch 36680
Item# 37 Draft Cap (Exhaust) 38141
Item# 45 Exhaust Wall Gasket 37956
Item# 50 Blower Wheel 34099
Item# 51 Electrode (Single Sense) 34570
*Not Shown* Single Sense Electrode Gasket 37100
Item# 51 Electrode (Dual Sense) 36997
*Not Shown* Dual Sense Electrode Gasket 32172
Item# 52 Limit Switch 37021
Item# 53 Burner Assembly 35491
Item# 55 Blower Assembly 34014
Item# 60 Igniter Lead 34571
*Not Shown* Wiring Service Kit 30007 NLA

Available Downloads:

Atwood

Atwood 8940 Iii Dclp Troubleshooting

  • Atwood 8940-DC-III Time Delay, Sail Switch, And Limit Switch Important Info
Furnace won't ignite

Atwood 8940-iii-dclp Troubleshooting

NEW

Atwood 8940 Iii Dclp Troubleshooting


Atwood Model 8940-iii-dclp Parts

I found that my atwood 8531 furnace would not ignite unless I pounded on the side of the furnace. After doing some research and reading many blogs I took my furnace apart and looked at the control board. Nothing was burned on it and the green light was blinking once and then again 3 seconds later. I looked up the codes and it said something about air blockage. There was nothing in line of the fresh air intake. When this happens it is most likely the sail switch. The sail switch tells the unit that there is plenty of air flow and it is safe to continue firing the furnace up. The furnace is rated to be safe and not ignite if the blower doesn't produce enough air flow(70%). The sail switch is located on the underside of the blower motor (squirrel cage) housing. The switch is held in by two screws. It has been known for these switches to burn out and not allow the furnace to work. I called atwood and they said that because this furnace was discontinued that there was no replace part listed for the sail switch. I was told I would most likely have to purchase a new furnace. I went on amazon and found this switch, Atwood 36680 Sail Switch. The switch costs me $4.95 and was sent in three days. I put this switch in and the furnace fired right up. Please do this before taking your furnace in to be fixed. This was an easy fix and saved me hundreds of dollars. Good luck. Any questions you can contact me at mmd2791@yahoo.com. No charge for what I know. Thanks